APT tarafından üretilmekte olan AC Güç Kaynaklarına ilişkin bilgiler aşağıda verilmektedir. 

Her türlü detay bilgi ve talebiniz için bizlerle temasa geçmenizi rica ederiz.

300XAC Serisi Modüler AC GÜÇ KAYNAKLARI     pdf katalog

APT tarafından imal edilmekte olan 300XAC Serisi Modüler AC Güç Kaynakları ileri düzey uygulamalar için gerekli olan en son teknolojik yenilikleri içermektedir, cihazların sahip olduğu smartDETECT™ özelliği sayesinde kullanıcı tarafından ilave bir ayara gerek olmaksızın her bir modülün master / slave (sunucu/hizmetçi) durumu otomatik olarak ayarlanmakta,  böylece 1-Fazlı veya 3-Fazlı çıkışa ve 18kVA'ya kadar arttırılabilen bir güce sahip modüler güç kaynağı imkanına sahip olunabilmektedir.  Kolay kullanımlı tuş takımı ve LCD gösterge ile 1Ф veya 3Ф  çalışma seçilebilmekte, testlerin programlanması ve yapılabilmesi sağlanmakta, anlık voltaj değişimlerinin simülasyonu için voltaj artımı ve düşümü sağlanabilmektedir.  Hiç bir ilave maliyet olmaksızın cihazların USB, Ethernet, RS232 veya GPIB ile PC'ye bağlanarak kontrol edilebilmesi sağlanabilmektedir.   Our 300XAC Series modular AC power sources incorporate the latest in modular technology, making them ideal for advanced applications. These versatile AC power sources can be configured for 1Ø stand-alone operation or linked together for up to 18 kVA of AC power in both 1Ø and 3Ø output configurations. Our smartDETECT™ feature automatically assigns the appropriate master/slave designation for each source without the need for the operator to reconfigure internal hardware. The easy-to-use push button interface allows the operator to select 1Ø and 3Ø operation, setup and perform tests, and simulate the effect of voltage surges and drops for transient testing. The 300XAC Series can be controlled with a PC from a variety of different interfaces – All at no extra cost! Choose from USB, Ethernet, RS-232 and GPIB.  Series Features Modular design allows operator to connect up to 3 instruments together for 1Ø or 3Ø applications requiring up to 18kVA of AC power Configure 2 sources for 1Ø/2W output voltages up to 600VAC smartCONFIG™ of master/slave instruments for easy 1Ø/3Ø setup 50 built-in memory locations with 9 test steps can be linked to quickly store and recall test parameters for multiple product testing applications Transient feature simulates voltage variations, brownouts and transient voltage conditions Adjust the starting and ending angle of the output waveform Constant current output with over current fold back feature Advanced metering circuits monitor voltage, current, peak current, power, apparent power, reactive power, power factor, and crest factor Rotary knob to adjust voltage and frequency on the fly External voltage sensing for accurate metering DC output standard Standard USB/RS-232 interface with no charge optional Ethernet and GPIB interfaces available CE Marked *  smartDETECT™ - this feature automatically determines how many 300XAC modular AC power sources are connected together in a power system. After the check is completed the 300XAC Series will automatically change the programming output function based on the number of interconnected sources in the system. *  Modular - capability that allows the operator to interconnect multiple 300XAC power sources in order to increase the power output or power configuration beyond that of a single instrument.   APT MODEL 310XAC   310XAC - 1Ø 1kVA / 3Ø 3kVA Modular AC Power Source    APT MODEL 320XAC   320XAC - 1Ø 2kVA / 3Ø 6kVA Modular AC Power Source    APT MODEL 340XAC   340XAC - 1Ø 4kVA / 3Ø 12kVA Modular AC Power Source    APT MODEL 360XAC   360XAC - 1Ø 6kVA / 3Ø 18kVA Modular AC Power Source    Quick Specs 1 kVA Power Rating Max Current: 9.2 A @ 110 V, 4.6 A @ 220 V Dimensions: (W x H x D) 16.9 x 5.2 x 20.8 in (430 x 133.5 x 530 mm) Weight: 44 lbs (20 kg) USB/RS-232 Standard A Closer Look Modular AC power source Configure for 3Ø, 3 kVA output or 1Ø/2W output voltages up to 600VAC Simulate transient conditions CE Marked Quick Specs 2 kVA Power Rating Max Current: 18.4 A @ 110 V, 9.2 A @ 220 V Dimensions: (W x H x D) 16.9 x 5.2 x 20.8 in (430 x 133.5 x 530 mm) Weight: 46.3 lbs (21 kg) USB/RS-232 Standard A Closer Look Modular AC power source Configure for 3Ø, 6 kVA output or 1Ø/2W output voltages up to 600VAC Simulate transient conditions CE Marked Quick Specs 4 kVA Power Rating Max Current: 36.8 A @ 110 V, 18.4 A @ 220 V Dimensions: (W x H x D) 16.9 x 10.5 x 19.7 in (430 x 267 x 500 mm) Weight: 110 lbs (50 kg) USB/RS-232 Standard A Closer Look Modular AC power source Configure for 3Ø, 12 kVA output or 1Ø/2W output voltages up to 600VAC Simulate transient conditions CE Marked Quick Specs 6 kVA Power Rating Max Current: 55.2 A @ 110 V, 27.6 A @ 220 V Dimensions: (W x H x D) 16.9 x 15.8 x 19.7 in (430 x 400.5 x 500 mm) Weight: 116.8 lbs (53 kg) USB/RS-232 Standard A Closer Look Modular AC power source Configure for 3Ø, 18 kVA output or 1Ø/2W output voltages up to 600VAC Simulate transient conditions CE Marked Available Options GPIB Interface for PC Control Ethernet Interface for PC Control 7 Memory Recall Grounded Neutral Linking Card   pdf manual   WHITE PAPERS White Papers and Technical Articles 5/2010 Understanding the Difference between Resolution and Accuracy Description This whitepaper discusses the difference between Resolution and Accuracy as it pertains to electronic equipment and ac power sources.  pdf 5/2010 True vs. Apparent Power This whitepaper defines the difference between True Power and Apparent Power and explains the various aspects of power.  pdf 4/2010 Power Factor vs. Crest Factor Two critical quantities to specify when dealing with AC power sources are the power factor (PF) and the crest factor (CF). This paper will define each metric and explain how they relate to electrical systems.  pdf 3/2010 Power Factor Correction This whitepaper discusses power factor correction (PFC), which is a commonly employed method to reduce harmonic distortion and increase efficiency in an AC power source.  pdf                         GLOSSARY OF TERMS Alternating Current (AC) - current that reverses direction on a regular basis (usually 60 times per second in the United States). Measured in amps. AC Power Source - an instrument that takes one AC voltage and frequency level and converts it into another AC voltage and frequency level. Amplifier - a circuit that boosts an input signal from one level to another. Apparent Power - the total power generated or consumed by a device due to real and reactive circuit components. Measured in VA (volt-amps). Complex Power - the vector sum of the real and reactive power components of a circuit. Measured in VA (volt-amps). Crest Factor - the ratio of peak current (Apeak) to RMS current (Arms). Direct Current (DC) - current that only flows in one direction. Direct current comes from a polarized source, meaning one terminal is always at a higher potential than the other. Measured in amps. Frequency - the number of times a waveform completes a cycle in a period of time. Measured in hertz. Inrush Current - a term used to describe the current needed to power a load upon start-up. Some loads require a large/inrush starting current in order to operate. Linear Power Source - a power source that linearly amplifies the input signal using transistors to increase the voltage, current and power output of the system. Modular - capability that allows the operator to interconnect multiple 300XAC power sources in order to increase the power output or power configuration beyond that of a single instrument. GLOSSARY OF TERMS OC Fold - over current fold back is a technology used in power sources that keeps output current constant by reducing the voltage in order to power loads that may have a high inrush current. Parallel Mode - up to 3x 300XAC modular AC power sources can be configured with their outputs tied in parallel, allowing for the system to output three times a single instrument's nominal output current rating. Phase Angle - the degree of measurement that corresponds to an AC waveform's amplitude. Measured from 0 - 360 degrees. PLC - Programmable Logic Control is an automation method using relay or digital technology. Polyphase Mode - multiple 300XAC modular AC power sources can be configured to provide output voltages of up to 600VAC (output configured for 1Φ3W) or provide 3Φ output power (output configured for 3Φ4W). Power - a generic term used to describe electrical work being done. There are many types of power, including real power, reactive power, apparent power, and complex power. Power factor - the ratio of real power (watts) to apparent power (VA). Based on a scale from 0 to 1 to determine how reactive and resistive a load is. Reactive Power - the power absorbed by capacitive or inductive elements in a circuit. This power does not work. Measured in VAR (volt-amps reactive). Real Power - the power that performs work in a circuit. Measured in watts. Response Time - the time that is needed to regulate the voltage, current, frequency, and power output when a load is added to the power source. Safety Agency Listing - a safety mark given to a product that has met stringent benchmarks as classified by the authorized agency.     GLOSSARY OF TERMS smartCONFIG™ - this feature enables the operator to change the output of linked 300XAC modular AC power sources from Parallel to Polyphase modes with a simple button push. No changing cables or test fixtures is required. smartDETECT™ - this feature automatically determines how many 300XAC modular AC power sources are connected together in a power system. After the check is completed the 300XAC Series will automatically change the programming output function based on the number of interconnected sources in the system. Start/End Angle - an APT feature that allows the operator to specify at which phase angle the output waveform begins and ends. Steady State Current r - a term used to describe the current when the load is running nominally after the inrush current. Surge/Drop - an APT feature that allows the test operator to simulate loading, brown-outs, and voltage dips and spikes. Switching Power Source - a power source that uses switching technology (integrated circuits and components) to increase the voltage, current and power output of the system. Synch Output - an APT feature that provides a 5V output signal which can be used to trigger a Programmable Logic Controller (PLC) device. Total Harmonic Distortion (THD) - a percentage that is used to identify the degree of the noise/unclean signal in a power source's output waveform. Transient - a temporary change in voltage or current that can occur which may alter the behavior of a DUT. APT instruments can simulate these conditions with our Surge/Drop feature. Voltage - the amount of force that is needed to move current from point to point. Measured in volts.     AŞAĞIDA YER ALAN ÜRÜNLER SADECE BİLGİLENDİRME AMACIYLA YER ALMAKTADIR, BU ÜRÜNŞER İÇİN SATIŞIMIZ BULUNMAMAKTADIR.

5000 Serisi Manual

AC GÜÇ KAYNAKLARI

Broşür :  

• 4 LED displays to monitor voltage, amps, frequency, power and power factor
• Range key for 0-150 V & 0-300 V
• System key to change set-ups
• Up/Down keys to change parameters
• 3 memory programs to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle to handle multiple country configurations
• Programmable settings of On/Off/Last for the power on status of the instrument
• Adjustable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Switching technology & direct coupled output reduces overall size and weight

6000 Serisi Otomatik

AC GÜÇ KAYNAKLARI

Broşür :

• Graphic liguid crystal display clearly shows voltage, amps, frequency, power and power factor
• Numeric key pad for the setting of test parameters
• 50 memory programs with 9 steps per memory to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle on rear panel for multiple country configurations
• Programmable settings of On/Off/Last for the power on status of the instrument
• Fully programmable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• PLC output for Pass/Fail/Test-in-Process
• RS-232 interface standard, and GPIB interface optional for computer instrument control
• Switching technology & direct coupled output reduces overall size and weight

Manual 500 VA AC Power Source

The 5005 is a 500 VA switching AC Power source. This power source provides a variable output voltage from 0-300 V, and output frequencies from 40-450 Hz. The input voltage is selectable for 115/230 with an input frequency from 47-500 Hz. The 5005 comes complete with 4 LED displays to easily monitor voltage, current, frequency, and power or power factor simultaneously. Each parameter of voltage, current, and frequency is programmable via our dedicated function keys. The 5005 also provides 3 programmable memories for easy test setup recall. In addition, it also provides several enhanced features such as over current fold back, overload current capacity, along with an inrush current rating of 4 times the maximum current.

• 500 VA Power Rating
• 4 LED displays to monitor voltage, amps, frequency, power and power factor
• Range key for 0-150 V & 0-300 V
• System key to change set-ups
• Up/Down keys to change parameters
• 3 memory programs to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle to handle multiple country configurations
• Programmable settings of On/Off/Last for the power on status of the instrument
• Adjustable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Lockout key to disable front panel operation
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating
• Overload current capacity of 4 times the current rating for 1 second
• Front panel calibration
• Output voltage 0-300 VAC
• Output frequency 40-450 Hz
• Input voltage 115/230 V
• Input frequency 47-500 Hz
• Switching technology & direct coupled output reduces overall size and weight

Full featured 500VA AC Power Source

The 6005 is a full featured switching 500VA AC power source. This programmable power source comes standard with a RS-232 interface for computer control or with optional GPIB. The 6005 provides variable output voltage from 0-300 V and output frequencies from 40-500 Hz. The input voltage is selectable between 115/230 with an input frequency from 47-500 Hz. The 6005 AC power source includes a graphic liquid crystal display that enables the operator to monitor voltage, frequency, current, peak current, power, and power factor simultaneously. Each parameter can be programmed independently along with other parameters such as ramping of voltage, testing time, as well as high & low limits. The 6005 AC power source also provides 50 programmable memories with 9 steps for connecting routines. A lockout feature is also available to protect pre-programmed routines.

The 6005 AC power source offers enhanced features which are ideal for a variety of power applications. The front panel rotary knob allows for instant adjustments of voltage and frequency while testing. The operator also has control of the start/end angle of the wave form, along with programming surge/drop cycles. Additionally, the operator can program the unit for an auto looping cycle and auto run mode which is ideal for burn-in/life cycle testing.

• 500 VA Power Rating
• Graphic liquid crystal display clearly shows voltage, amps, frequency, power and power factor
• Numeric key pad allows for the easy setting of test parameters
• 4 soft keys for menu selections
• Encoder wheel to adjust voltage and frequency during the test
• Universal receptacle on front panel to handle multiple country configurations
• Test/Reset key to activate and disable output
• Lockout key to disable front panel operation
• PLC output for Pass/Fail/Test-in Process
• RS-232 interface standard, and GPIB interface optional for computer instrument control
• Synch output to trigger a PLC device that requires a 5 Volt signal
• Input 47-500 Hz
• Input voltage 115/230
• Voltage output 0-300 VAC
• Frequency output 40-500 Hz
• Measurement of voltage, frequency, amps, apparent power, power and power factor
• 50 memory programs with 9 steps per memory to store and quickly recall test programs
• Programmable steps to link tests
• Fully programmable high/low limits for voltage, amps, and frequency
• Programmable test time, delay time, and ramp timers
• Programmable surge/drop voltage simulates loading, brown outs or voltage dips
• Programmable start/end angle provides the ability to monitor current conditions under different starting / ending angles of the sine wave.
• Burn in testing capability with auto loop cycle, auto run mode, time selectable seconds/minutes/hours
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating for 1 second
• Prompt feature to add instructions to a test
• Front panel calibration
• Switching technology & direct coupled output reduces overall size and weight

Manual 1 KVA AC Power Source

The 5010 is a 1 KVA switching AC Power source. This power source provides a variable output voltage from 0-300 V and output frequencies from 40-450 Hz. The input voltage is selectable for 115/230 with an input frequency from 47-500 Hz. The 5010 comes complete with 4 LED displays to easily monitor voltage, current, frequency, and power or power factor simultaneously. Each parameter of voltage, current, and frequency is programmable via our dedicated function keys. The 5010 also provides 3 programmable memories for easy test setup recall. In addition, it also provides several enhanced features such as over current fold back, overload current capacity, along with an inrush current rating of 4 times the maximum current.

• 1 KVA Power Rating
• 4 LED displays to monitor voltage, amps, frequency, power and power factor
• Range key for 0-150 V & 0-300 V
• System key to change set-ups
• Up/Down keys to change parameters
• 3 memory programs to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle to handle multiple country configurations
• Programmable settings of On/Off/Last for the power on status of the instrument
• Adjustable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Lockout key to disable front panel operation
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating
• Overload current capacity of 4 times the current rating for 1 second
• Front panel calibration
• Output voltage 0-300 VAC
• Output frequency 40-450 Hz
• Input voltage 115/230 V
• Input frequency 47-500 Hz
• Switching technology & direct coupled output reduces overall size and weight

Full featured 1 KVA AC Power Source

The 6010 is a full featured switching 1 KVA AC power source. This programmable power source comes standard with a RS-232 interface for computer control or with optional GPIB. The 6010 provides variable output voltage from 0-300 V and output frequencies from 40-500 Hz. The input voltage is selectable between 115/230 with an input frequency from 47-500 Hz. The 6010 AC power source includes a graphic liquid crystal display that enables the operator to monitor voltage, frequency, current, peak current, power, and power factor simultaneously. Each parameter can be programmed independently along with other parameters such as ramping of voltage, testing time, as well as high & low limits. The 6010 AC power source also provides 50 programmable memories with 9 steps for connecting routines. A lockout feature is also available to protect pre-programmed routines.

The 6010 AC power source offers enhanced features which are ideal for a variety of power applications. The front panel rotary knob allows for instant adjustments of voltage and frequency while testing. The operator also has control of the start/end angle of the wave form, along with programming surge/drop cycles. Additionally, the operator can program the unit for an auto looping cycle and auto run mode which is ideal for burn-in/life cycle testing.

• 1 KVA Power Rating
• Graphic liquid crystal display clearly shows voltage, amps, frequency, power and power factor
• Numeric key pad allows for the easy setting of test parameters
• 4 soft keys for menu selections
• Encoder wheel to adjust voltage and frequency during the test
• Universal receptacle on front panel to handle multiple country configurations
• Test/Reset key to activate and disable output
• Lockout key to disable front panel operation
• PLC output for Pass/Fail/Test-in Process
• RS-232 interface standard, GPIB interface optional for computer instrument control
• Synch output to trigger a PLC device that requires a 5 Volt signal
• Input 47-500 Hz
• Input voltage 115/230
• Voltage output 0-300 VAC
• Frequency output 40-500 Hz
• Measurement of voltage, frequency, amps, apparent power, power and power factor
• 50 memory programs with 9 steps per memory to store and quickly recall test programs
• Programmable steps to link tests
• Fully programmable high/low limits for voltage, amps, and frequency
• Programmable test time, delay time, and ramp timers
• Programmable surge/drop voltage simulates loading, brown outs or voltage dips
• Programmable start/end angle provides the ability to monitor current conditions under different starting / ending angles of the sine wave.
• Burn in testing capability with auto loop cycle, auto run mode, time selectable seconds/minutes/hours
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating for 1 second
• Prompt feature to add instructions to a test
• Front panel calibration
• Switching technology & direct coupled output reduces overall size and weight

Manual 2 KVA AC Power Source

The 5020 is a 2 KVA switching AC Power source. This power source provides a variable output voltage from 0-300 V and output frequencies from 40-450 Hz. The input voltage is 208 V with an input frequency from 47-500 Hz. The 5020 comes complete with 4 LED displays to easily monitor voltage, current, frequency, and power or power factor simultaneously. Each parameter of voltage, current, and frequency is programmable via our dedicated function keys. The 5020 also provides 3 programmable memories for easy test setup recall. In addition, it also provides several enhanced features such as over current fold back, overload current capacity, along with an inrush current rating of 4 times the maximum current.

• 2 KVA Power Rating
• 4 LED displays to monitor voltage, amps, frequency, power and power factor
• Range key for 0-150 V & 0-300 V
• System key to change set-ups
• Up/Down keys to change parameters
• 3 memory programs to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle to handle multiple country configurations
• Adjustable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Lockout key to disable front panel operation
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating
• Overload current capacity of 4 times the current rating for 1 second
• Front panel calibration
• Output voltage 0-300 VAC
• Output frequency 40-450 Hz
• Input voltage 208 V (230 V optional)
• Input frequency 47-500 Hz
• Switching technology & direct coupled output reduces overall size and weight

Full featured 2 KVA AC Power Source

The 6020 is a full featured switching 2 KVA AC power source. This programmable power source comes standard with a RS-232 interface for computer control or with optional GPIB. The 6020 provides variable output voltage from 0-300 V and output frequencies from 40-500 Hz. The input voltage is 208 V with an input frequency from 47-500 Hz. The 6020 AC power source includes a graphic liquid crystal display that enables the operator to monitor voltage, frequency, current, peak current, power, and power factor simultaneously. Each parameter can be programmed independently along with other parameters such as ramping of voltage, testing time, as well as high & low limits. The 6020 AC power source also provides 50 programmable memories with 9 steps for connecting routines. A lockout feature is also available to protect pre-programmed routines.

The 6020 AC power source offers enhanced features which are ideal for a variety of power applications. The front panel rotary knob allows for instant adjustments of voltage and frequency while testing. The operator also has control of the start/end angle of the wave form, along with programming surge/drop cycles. Additionally, the operator can program the unit for an auto looping cycle and auto run mode which is ideal for burn-in/life cycle testing.

• 2 KVA Power Rating
• Graphic liquid crystal display clearly shows voltage, amps, frequency, power and power factor
• Numeric key pad allows for the easy setting of test parameters
• 4 soft keys for menu selections
• Encoder wheel to adjust voltage and frequency during the test
• Universal receptacle on front panel to handle multiple country configurations
• Test/Reset key to activate and disable output
• Lockout key to disable front panel operation
• PLC output for Pass/Fail/Test-in Process
• RS-232 interface standard, GPIB interface optional for computer instrument control
• Synch output to trigger a PLC device that requires a 5 Volt signal
• Input 47-500 Hz
• Input voltage 208 V (230 V optional)
• Voltage output 0-300 VAC
• Frequency output 40-500 Hz
• Measurement of voltage, frequency, amps, apparent power, power and power factor
• 50 memory programs with 9 steps per memory to store and quickly recall test programs
• Programmable steps to link tests
• Fully programmable high/low limits for voltage, amps, and frequency
• Programmable test time, delay time, and ramp timers
• Programmable surge/drop voltage simulates loading, brown outs or voltage dips
• Programmable start/end angle provides the ability to monitor current conditions under different starting / ending angles of the sine wave.
• Burn in testing capability with auto loop cycle, auto run mode, time selectable seconds/minutes/hours
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating for 1 second
• Prompt feature to add instructions to a test
• Front panel calibration
• Switching technology & direct coupled output reduces overall size and weight

Manual 4 KVA AC Power Source

The 5040 is a 4KVA switching AC Power source. This power source provides a variable output voltage from 0-300 V and output frequencies from 40-450 Hz. The input voltage is 208 V with an input frequency from 47-500 Hz. The 5040 provides 4 LED displays to easily monitor voltage, current, frequency, and power or power factor simultaneously. Each parameter of voltage, current, and frequency is programmable via our dedicated function keys. The 5040 also provides 3 programmable memories for easy test setup recall. In addition, it also provides several enhanced features such as over current fold back, overload current capacity, along with an inrush current rating of 4 times the maximum current.

• 4 KVA Power Rating
• 4 LED displays to monitor voltage, amps, frequency, power and power factor
• Range key for 0-150 V & 0-300 V
• System key to change set-ups
• Up/Down keys to change parameters
• 3 memory programs to store and quickly recall test programs
• Test/Reset key to activate and disable output
• Universal receptacle to handle multiple country configurations
• Programmable settings of On/Off/Last for the power on status of the instrument
• Adjustable high/low limits for voltage, amps, and frequency
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Lockout key to disable front panel operation
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating
• Overload current capacity of 4 times the current rating for 1 second
• Front panel calibration
• Output voltage 0-300 VAC
• Output frequency 40-450 Hz
• Input voltage 208 V (230 V optional)
• Input frequency 47-500 Hz
• Switching technology & direct coupled output reduces overall size and weight

Full featured 4 KVA AC Power Source

The 6040 is a full featured switching 4 KVA AC power source. This programmable power source comes standard with a RS-232 interface for computer control or with optional GPIB. The 6040 provides variable output voltage from 0-300 V and output frequencies from 40-500 Hz. The input voltage is 208 V with an input frequency from 47-500 Hz. The 6040 AC power source includes a graphic liquid crystal display that enables the operator to monitor voltage, frequency, current, peak current, power, and power factor simultaneously. Each parameter can be programmed independently along with other parameters such as ramping of voltage, testing time, as well as high & low limits. The 6040 AC power source also provides 50 programmable memories with 9 steps for connecting routines. A lockout feature is also available to protect pre-programmed routines.

The 6040 AC power source offers enhanced features which are ideal for a variety of power applications. The front panel rotary knob allows for instant adjustments of voltage and frequency while testing. The operator also has control of the start/end angle of the wave form, along with programming surge/drop cycles. Additionally, the operator can program the unit for an auto looping cycle and auto run mode which is ideal for burn-in/life cycle testing.

• 4 KVA Power Rating
• Graphic liquid crystal display clearly shows voltage, amps, frequency, power and power factor
• Numeric key pad allows for the easy setting of test parameters
• 4 soft keys for menu selections
• Encoder wheel to adjust voltage and frequency during the test
• Universal receptacle on front panel to handle multiple country configurations
• Test/Reset key to activate and disable output
• Lockout key to disable front panel operation
• PLC output for Pass/Fail/Test-in Process
• RS-232 interface standard, GPIB interface optional for computer instrument control
• Synch output to trigger a PLC device that requires a 5 Volt signal
• Input 47-500 Hz
• Input voltage 208 V (230 V optional)
• Voltage output 0-300 VAC
• Frequency output 40-500 Hz
• Measurement of voltage, frequency, amps, apparent power, power and power factor
• 50 memory programs with 9 steps per memory to store and quickly recall test programs
• Programmable steps to link tests
• Fully programmable high/low limits for voltage, amps, and frequency
• Programmable test time, delay time, and ramp timers
• Programmable surge/drop voltage simulates loading, brown outs or voltage dips
• Programmable start/end angle provides the ability to monitor current conditions under different starting / ending angles of the sine wave.
• Burn in testing capability with auto loop cycle, auto run mode, time selectable seconds/minutes/hours
• Over current fold back reduces output current linearly to the voltage in order to power loads that have a high inrush current
• Enhanced protection circuits
• Crest factor of 3
• Inrush current of 4 times the current rating for 1 second
• Prompt feature to add instructions to a test
• Front panel calibration
• Switching technology & direct coupled output reduces overall size and weight